MOOV MINISALT • PRACTICAL GUIDE • PISCINE HIPPOCAMPE
The right amount of salt.
A properly adjusted production setting.
A well-maintained cell.
Your MiniSalt produces chlorine for your pool from the salt dissolved in the water. To get the most out of it, you need to understand three things: the salt level, the production setting, and the condition of the cell.
Here are Piscine Hippocampe's guidelines for using your MOOV system every day, covering the key points from the technical manual and our maintenance tips.
Discover MiniSalt →
Our current salt target in normal NS mode, following the MOOV guidance shared by our team.
Our free chlorine reference level, to be maintained through testing and adjustments.
A production setting. It never means "10 ppm of chlorine" in the water.
1. Keep the salt around 4,000 ppm in NS mode
For MiniSalt systems used in normal salt mode (NS), Piscine Hippocampe now recommends aiming for 4,000 ppm, following the MOOV guidance shared with our team. This reference applies to NS mode; low salt mode (LS) uses different settings.
You may have an older document showing a different NS reference level. The technical manual we consulted mentions 3,000 to 3,200 ppm in its troubleshooting section, among other things. Have the mode and current setting for your model confirmed before adjusting the water.
Does more salt mean more chlorine?
Dissolved salt allows the water to conduct the electricity needed for electrolysis. Too little salt can limit production or trigger an alarm. Returning to the appropriate level helps the cell operate under the right conditions.
The goal is to reach the target, then maintain it. Beyond that, adding more salt is not a way to adjust chlorine. Production also depends on the setting, circulation time, water balance, and the condition of the cell.
2027 season: a MOOV electronic pen included
For the 2027 season, salt systems sold at Piscine Hippocampe include a MOOV electronic pen for measuring salt. Use it to check the actual concentration before each addition.
Follow the pen's instructions for its measurement method, calibration, and maintenance. The reading you want is salinity in ppm; a salt test does not measure chlorine, pH, or alkalinity.
Salt does not evaporate with water. So a drop in water level due to evaporation does not justify automatically adding salt. However, water loss, filter backwashing, and water replacement can change the salinity: measure before making adjustments.
Add only the amount needed
- Measure the salt level and confirm the pool’s actual volume.
- Calculate the difference between the current concentration and the target.
- Turn off chlorine production while adding salt and maintain proper circulation.
- Spread the salt directly in the pool, away from the skimmer, and brush away any buildup.
- Let it dissolve completely, then measure again before producing chlorine.
The manual recommends running filtration for 24 hours to allow the salt to dissolve. Also follow the instructions for your salt and equipment.
Our choice: Pristiva Premium salt
We strongly recommend Pristiva Premium high-purity salt. Salt quality matters: unwanted impurities can complicate maintenance and contribute to deposits or water appearance problems.
High-purity salt designed for pools and formulated to dissolve effectively is a good starting point. It does not eliminate the need to monitor the water and the cell.
2. Set to 10, test the chlorine, then reduce
The MiniSalt produces chlorine automatically, but it does not adjust production based on your test results. You need to choose the right level for your pool. On the version described in the manual, 00 is standby and 10 is 100%.
Once the water is clear and balanced, the salt has dissolved, and circulation is established, our startup approach is to start at level 10, or 100%, then measure free chlorine and lower the setting to maintain our target range of about 1 to 3 ppm.
Level 10 is a monitored starting point, not a setting to leave unchecked. If the chlorine is already sufficient, adjust production right from the start. A small pool or low demand may require a quick reduction.
- Test daily when starting up, then regularly once the setting has stabilized.
- Reduce production if the chlorine rises above the target.
- If chlorine is low, also check the filtration time, salt level, pH, cell, and pool demand.
- After heavy use or a change in weather, test again and adjust.
The amount produced depends on the selected level and how long the water circulates and the cell operates. A unit set to 10 does not necessarily make up for insufficient filtration time.
If the water is green or chlorine is insufficient, correct the situation before swimming. Do not rely solely on waiting at level 10 to quickly restore problematic water.
Boost: temporary support
Boost mode temporarily increases production, then returns to the normal setting after 24 hours, according to the manual. It may be useful when demand increases. This is not a complete shock treatment and is not enough to clear green water. Consult the instructions for your version to activate it.
3. Water balance remains essential
Before startup, the manual calls for clear water, free of algae and sediment. Here are the reference values from the version consulted, to be interpreted alongside your test results and maintenance program.
| Parameter | Manual reference |
|---|---|
| pH | 7.2 to 7.8 |
| Alkalinity | 80 to 120 ppm |
| Calcium hardness | 200 to 300 ppm |
| Stabilizer (CYA) | Less than 30 ppm |
| Phosphates | Less than 300 ppb |
Hard water and an unfavorable balance can promote scale. The manual also identifies phosphates as a cause in cases of premature fouling. Testing helps target the correction instead of adding more products.
Choose the Solei program with our team: do not automatically add stabilizer just to reach a number. Also see our pool water balancing guide.
4. Solei by Dazzle: our recommendation to support pool maintenance
We strongly recommend Solei by Dazzle as part of a program suited to your pool. This oxidizer uses sunlight to support the oxidation of organic contaminants and help keep water clear.
It complements the work of the disinfection program. The cell remains responsible for chlorine production, and testing is still necessary. Follow the label directions for the water volume and selected program.
Discover Solei by Dazzle →5. Inspecting the cell: the owner’s responsibility
Depending on water hardness and the pool environment, scale may form on the plates. The owner must check the cell’s condition and arrange for its maintenance. Polarity reversal does not replace inspection.
The manual provides for an adjustment of the reversal frequency based on hardness: harder water may require more frequent reversals. Have this setting checked based on a water test rather than changing it at random.
The MOOV base and Pristiva cleaner have two different functions
Your duo for cleaning the cell
Add 1 MOOV cleaning holder and 1 Pristiva Salt Cell Cleaner together to prepare for maintaining your MiniSalt or JustSalt cell.
One of each product. You can check the quantities in your cart.
Best practices for cleaning
- Turn off the chlorinator and pump, disconnect the necessary power supplies and release the pressure in the system according to the instructions before removing the cell.
- Inspect the plates and confirm whether cleaning is needed.
- Use the appropriate holder and Pristiva Salt Cell Cleaner according to their instructions and those for the cell.
- Follow the protection, contact time and rinsing instructions on the label.
- Rinse, reinstall correctly, check for leaks and flow, then resume production.
Do not scrape the plates with a metal tool or mix cleaning products. Clean according to the condition observed and applicable instructions, without unnecessary repeated soaking.
6. The MOOV dummy: very useful when the cell is removed
We strongly recommend purchasing the MOOV dummy for the start and end of the season, when you prefer to remove the cell while circulating cold water, as well as during an inspection, cleaning or cell issue.
It temporarily replaces the cell in the plumbing. With a compatible part, a watertight connection and the system restored to operating condition, the pump and filtration system can continue circulating the water.
See the MOOV dummy →The dummy does not produce any chlorine. The chlorinator remains off while the cell is removed. Maintain sanitation using an appropriate method and test the water. Turn off the pump and release the pressure before replacing anything.
The dummy makes transition periods easier; complete closure and freeze protection follow a separate winterization procedure.
7. Lights and alarms: what should you check first?
The green light indicates that the unit is operating and producing. It does not confirm that the pool’s chlorine is at the correct level. A red light indicates a problem that may prevent production.
A1: production anomaly
Check the salt with an independent measurement, make sure the cell is full, and check for scale. The manual also lists connections and an equipment problem among the possible causes.
Fix the cause before restarting the system. If the code persists, contact our team; hiding the alarm will not fix the problem.
OF: no flow detected
Check whether the pump is running, water is circulating, and the cell is full. The flow sensor or its connection could also be the cause.
Do not bypass the sensor. Production must remain off until circulation is restored.
To help us, note the model, exact code, measured salt level, free chlorine, pH, and filtration hours. Add a photo of the display and cell. Electrical tests inside the unit should be left to a technician.
Your MiniSalt routine in five steps
- Test: Chlorine and water balance, more often at startup or when conditions change.
- Measure the salt: Before adding salt and after significant water dilution.
- Adjust: Adjust production and filtration time according to the results.
- Inspect: Check the cell, deposits, flow, and visible condition of the installation.
- Prepare for transitions: Keep the support, cleaner, and dummy handy for seasonal maintenance.
Products to have on hand at Piscine Hippocampe
Choosing a system? Compare the MiniSalt MC50MINI → and the MiniSalt MC85MINI →. Pool volume, NS or LS mode, and chlorine demand affect sizing. Our salt system comparison can help you prepare for the discussion.
Your MiniSalt, with the right guidelines
Questions about salt, settings, or cleaning? The Piscine Hippocampe team in Delson can help you interpret your results and choose the right products.
Bring your readings and equipment model details for accurate advice.
Contact us at 450 632-8680Guide based on the MOOV MiniSalt technical manual and advice from Piscine Hippocampe. The target of about 4,000 ppm applies to NS mode and reflects the current MOOV recommendation shared by our team. The instructions for your installed model and product labels specify the applicable procedures. View the manufacturer's information.